How To Create Texture Using Polishing Tools

There are many ways to add texture to your jewellery – burrs, files and waxes are examples of techniques that add deep and pronounced texture to once plain surfaces.

Here we are going to show you a few quick and easy ways to add texture using a range of polishing tools, including our favourite the Garryflex.

Step 1:

To show examples of a few different textures we have cut out triangles to make into mix and match studs.

Mark out the size of your triangles onto the metal using a scribe. Cut out using your piercing saw, sawing on the outside of the line to leave room for filing or sanding later. Also, remember to keep that blade lubricated! We recommend having a block of wax screwed to your bench, easy to hand, to ensure your blade remains lubricated.

Sanding

You need to give yourself a good clean tidy base to work with, texture will not hide any marks or scratches and can highlight them even more. If you cut corners you will have to go back and fix it later, so it’s better to get it right at this stage to avoid going back and starting all over again!

Work through the emery papers, from 150 grit to 1,200 grit. At each stage ensure all your scratches have gone from the previous grit before moving onto the next. If you have pieces that are the same size, sandwich everything together with a small amount of superglue and sand the edges all at once to save time

5 metal triangles stacked on top of each other

Step 2:

Now it’s time to texture. Here are just a few of the many different textures you can create…

No 1
Garryflex – coarse

Garryflex is effective, yet quick and easy to use. Simply add texture using any motion you like, linear, circles or crosshatch. We have used a light pressure with a flicking motion in random directions to achieve a raw edgy scratched look.

Garryflex next to a piece of scratched silver triangle

No 2
Frosting wheel – Yellow

Knife edge rubber wheel – Black

Firstly, remember to protect yourself as these frosting wheels can be dangerous. Wear safety goggles and protect your fingers. Hold small pieces in pliers to allow for a good grip and keep your fingers out of harms reach (You can also hold your piece in a ring clamp). Texture the entire surface with the frosting wheel using slow backwards and forwards movements. Next, I have added some stripes using the coarse black knife edge rubber wheel. Try and keep this straight and repeat a couple of times until you get the required depth to create a stunning contrast between the stripes and the shimmery texture.

knife edge rubber wheel being used on a clamped piece of silver

No 3
Nylon Abrasive wheel

Nylon Abrasive wheels gives a lovely matt finish. To give the piece interest use liner movements overlapping in a crisscross pattern.

nylon abrasive wheel next to a matt finish silver triangle

No 4
White extra coarse knife edge rubber wheel

Using the edge of the wheel create little lined divots that go in random directions and overlap, so the whole surface is filled but not too deeply, just enough to see the pattern. This creates a really interesting effect with added depth.

shows the edge of the white xtra course knife edge rubber wheel being used in random line movements

No 5
Matt finishing abrasive wheel

Simply move the wheel in only one direction to create a lovely linear and subtle satin finish.

shows a matt finishing abrasive wheel next to a matt silver triangle

No 6
Frosting wheel – Green
Covering the entire area, use straight even movements and repeat the process to emphasise the detail further. This is the coarsest of the frosting wheels and gives a really shimmery finish

polishing tools in a row

Step 3:

Soldering the posts
Ensure the backs of the triangles are clean, free from dirt and finger prints by giving a quick rub with 1,200 grit emery paper to allow the solder to flow easily. Line up your triangles on your soldering block and add a small amount of flux to the area where the post will be placed. You can measure and mark the point with a scribe or by eye.

Heat the solder pallions and scoop them onto the posts and then bring the post over to the piece, heat the piece and solder on the post. (You can also sweat solder the solder to the earring first and then add the post if you prefer). Quench in water and place in the pickle.

Step 4:

Final polish
Once out of the pickle the backs may need a bit of a clean-up. We recommend pink scotchbrite radial discs, which will clean up nicely without damaging the clean-up you did prior to pickling. If the fronts need a bit of attention, top up some textures or lightly polish any areas you would like to “pop” with a soft wool mop and rouge

soft wool mop being used on a stud earring

And there you have some little textured studs to mix and match. There is so many textures you can make using different tools, so have a play around and see what you create. Always remember to stay safe by wearing the correct PPE – enjoy!

We want to know what you’ve been making! Share your creations with us on social media, tagging in Cooksongold on Facebook, Twitter and Instagram

The post How To Create Texture Using Polishing Tools appeared first on The Bench.



source https://www.cooksongold.com/blog/learn/creating-texture-using-polishing-tools/?utm_source=rss&utm_medium=rss&utm_campaign=creating-texture-using-polishing-tools

Comments

Popular posts from this blog

How To Cut And Polish Gemstones By Hand

Filing metals: How to file flat, square and curved surfaces

Our Top 3D Design Software: The best picks for you