Chasing and Repoussé Techniques for Beginners

Chasing and repoussé has been used by jewellers from as early as the ancient civilisations in the Bronze Age, and even before. The technique picked up speed all around the world, being used in Ancient Egypt, Greece, India and Pre-Columbian America – and is still a skill sought after by many jewellers today. Although, getting the hang of chasing and repoussé can be challenging at first, it’s super rewarding once you’ve mastered it.

Find out more about the chasing and repoussé tools and techniques and what it actually is, below.

Using the chasing and repoussé technique

What is repoussé jewellery?

If you’re completely new to this technique, you might be wondering; “what is repoussé jewellery?”. Let’s start by decoding its name.

Chasing, originates from the French word ‘chasser’ meaning, ‘to chase’ as the technique involves pushing back the metal to make the design protrude forward.

In a similar vein, repoussé is another French word meaning ‘push up’, referring to the action of hammering behind the design to bring it forward at the front. The combination of these two methods produces a tactile design with an equally eye-catching look.

Chasing and repoussé tools

It’s important that you pick up all the right chasing and repoussé tools before you get started. Here’s what you’ll need:

Chasing and repoussé tools

Repousse Hammer

 

The chasing and repoussé technique: step by step

Now you know what repoussé jewellery is and the tools it requires, it’s time to talk you through the chasing and repoussé technique itself. Just follow the steps below to get going:

  1. Make your pitch. The first step in the chasing and repoussé process is to prepare your pitch. Use a heat gun, hand torch or powerful hairdryer to heat up the pitch, before pouring or pressing it into a pitch bowl. As an alternative, you could use a leather cushion filled with sand or grit which should function like a standard pitch.
  2. Prepare your design. Using either your pencil or marker pen, highlight the area on the front of the metal’s surface to indicate where it will be pushed out from the back. Once done, curl the corners of the sheet into the pitch to keep it steady.
  3. Punch in the design. Next, use the blunt chisel punch to mark out the design. To do this, repeatedly strike the chisel with your chasing hammer until you have followed the whole line. Make sure you’re holding the chisel correctly too, at a slight angle with your thumb on one side and fingers on the other – touching either the pitch or the metal for further support.

Top tip! You’ll need to strike the very top of the chisel with the flat end of the hammer, gently enough to make a smooth line that will show on the other side of the metal.

  1. Repoussé the metal. Take your repoussé hammer and punches, turn the metal over and hammer within the areas that you have just marked out. Is the metal too hard to mould? Quickly anneal your design, cool and then try again.
  2. Prepare for chasing. Once you’ve repousséd the metal, remove it from the pitch and clean it before chasing. If there’s any pitch still left on the design, lay it on a soldering table and use a flame over it, then you should see the residual pitch flake off. Quench the metal by placing it in cold water until it relaxes.
  3. Redraw the design. Using your pencil or marker pen, draw the outline of your design once more. When you’re done, add it to the pitch the same way as before, front side up. Now you’re ready for chasing.
  4. Use your chasing tools. Make the repousséd areas really stand out by using your punches and chasing tools to push the metal further down, all along the lines you’ve drawn. Looking to add a pattern to the background? You can use marked punches at a right angle to the design to add more detail, just make sure you’re annealing every time you switch sides. This action will make the corners of the metal become slightly distorted, but this isn’t a problem as you’ll be cutting it away.
  5. Finish off the piece. Once you’ve removed your work from the pitch, you’ll need to anneal it once more, followed by quenching. When it’s dry, put it on a metal flat plate with the design facing upwards, and use a large round punch to even out the sides. Then take a piercing saw and cut off the edges, before filing to finish. And you’re done!

Ready to give this chasing and repoussé technique a go yourself? Make sure that you’re fully prepared with all the jewellery tools you need before you start. For more on the different techniques and equipment you can use, check out the beginner’s guide section of our blog.

The post Chasing and Repoussé Techniques for Beginners appeared first on The Bench.



source https://www.cooksongold.com/blog/beginners-guides/chasing-and-repousse-techniques-for-beginners

Comments

Post a Comment

Popular posts from this blog

How To Cut And Polish Gemstones By Hand

Image
Wondering how to cut and polish gemstones by hand? Asking yourself “is it worth investing in tools for cutting and polishing gemstones”? Well, we’ve put together a selection of methods and tools for cutting and polishing gemstones without a machine. So whether you’re just getting a taste for lapidary, you’re trying to introduce it to your business, or your job involves gemstones on an everyday basis – we’ve got some ideas for you. How to cut and polish gemstones When you’re just starting out, try these techniques with a larger gemstone that has obvious flat surfaces with minimal dents, as this will make it easier to shape. And focus on creating just a few, large facets as these are easier to polish later on. How to cut gemstones by hand: using sandpaper A less technical, precise and a more free-hand way to cut and polish your gemstones – leaving out the tools is ideal for those who are just dabbling in gemstones without looking to sell just yet. Equipment: Chopping board Wet ...
Read more

Filing metals: How to file flat, square and curved surfaces

Image
Filing metal is an essential technique in jewellery making. Although simple in concept, following proven practices combined with the right filing techniques and  the right jewellery making files , ensures the job becomes a breeze. Filing metal: The basics What is a metal file used for? Filing is used in jewellery making to remove excess metal, even out surfaces, smooth or to shape, form and texture pieces. Are there specific files for certain tasks? There are several methods of filing metal and the actual  files  come in a variety of shapes, grades/cuts and sizes. The shape of the file you choose will depend on the job you are completing. For example  flat files  are used for straight edges or convex curves such as the outer edge of a disc, and  curved files  are used on concave curves such as the inside of rings. What does the “cut” of a file mean? The cut of each metal file type describes the arrangement of teeth and therefore the amount of m...
Read more

Our Top 3D Design Software: The best picks for you

Image
3D printing with Cooksongold is an incredible opportunity for creatives to unleash their imagination and produce a beautiful design that can be bought to life for you. Today’s blog in our 3D series will be the perfect guide to help any beginner or pro wanting to design, to choose the best 3D design software suited for you. While there are many different versions of free 3D modeling software available, the key is to find an efficient program that matches project requirements and provides the opportunity to make edits easily as product development moves forward. Quality 3D prints depend on a strong foundation, backed with solid designs and a growing knowledge of 3D modeling tools. Designers and engineers tend to rely on a handful of well-known 3D modeling software programs, serving as the building blocks for successful additive manufacturing of parts. Gaining skill in using 3D modeling tools takes time, and there is always room to improve and advance further as a 3D designer. Here ar...
Read more